Dfi TPC121 Installation Guide Bedienungsanleitung

1TPC121/150/170Installation Guidewww.d.com• 1 TPC121/150/170 Panel PC• 1 120W power adapter (only for model TPC-1212TR-SBDCR-R10)• 1 Quick Installati

10Installing a SATA Drive1. Locate the SATA drive bay in the chassis.SATA drive bayTPC121TPC150/ TPC170SATA drive bay

112. Remove the mounting screws that secure the HDD bracket to the drive bay. Mounting ScrewTPC121TPC150/ TPC170Mounting Screw

123. Align the mounting holes of the SATA drive with the mounting holes on the HDD bracket and then use the provided mounting screws to secure the dri

135. Connect one end to the SATA data connector on the SATA drive and the other end to the SATA data connector on the system board. Mounting

14SATA data connectorSATA data connectorSATA data connectorSATA power connectorSATA power connector

15Installing a Mini PCIe CardLatch1. Locate the two Mini PCIe slots on the chassis.Mini PCIe slotMini PCIe slot

162. The latch is used to lock the Mini PCIe card into position. Insert the latch into the mounting holes and then push the latch down until the clip

173. The system board is equipped with a Mini PCIe slot.The Mini PCIe slot supports half length Mini PCIe card. Note the key on the slot. The k

181. Grasping the Mini PCIe card by its edges, align the card into the slot at an approximately 30 degrees angle. Apply rm even pressure to each

19Mounting screwBracket2. Remove these mounting screws and brackets, and then put them in a safe place for later use.3. Insert the Expansion card with

2TPC121Front View Bottom View USBFunction KeysAlarm LEDHDD LEDPower LEDLine-inMic-inLine-outCOM 2COM 1PS/2 KBPS/2 MouseUSB 2.0+19V DC-in (default)Powe

201. Insert the cable end of the power adaptor to the terminal block. To rmly x the cable into the terminal block, use a screwdriver to cl

212. Plug the terminal block into the DC-in connector and then tighten the screws to secure the terminal block in place.DC-inconnectorScrews

22The wall mount kit includes the following:• 2 Wall mount brackets• Bracket screws1. Select a place on the wall where you will mount the Panel PC.

23Wall mount bracket 24. Using the hooks on “bracket 2”, slide the Panel PC to “bracket 1”.Wall mount bracket 2Mounting screwWall mount bracket

245. Tighten the screw to hold the assembly in place.Mounting screw

25241.00321.00Panel mountThe panel mounting kit includes the following:• 10 mounting clamps (TPC121 and TPC150)• 12 mounting clamps (TPC170)1. Sele

26Slit for mounting the clampMounting clampWhite plastic cap6. The rst and second clamps must be positioned and secured diagonally prior to mounti

27296.00386.00

28934-TPC121-000GA24601243Board Layout and Jumper SettingsClear CMOS JP9 Normal (default) 1-2 On Clear CMOS 2-3 OnPS/2 Power JP2

3TPC150Front View Bottom View USBFunction KeysAlarm LEDHDD LEDPower LEDLine-inMic-inLine-outCOM 2COM 1PS/2 KBPS/2 MouseUSB 2.0Power SwitchLANDVI-IHDMI

4TPC170Front View Bottom View USBFunction KeysAlarm LEDHDD LEDPower LEDLine-inMic-inLine-outCOM 2COM 1PS/2 KBPS/2 MouseUSB 2.0Power SwitchLANDVI-IHDMI

5Key FeaturesTPC121/150/170Processor3rd/2nd Generation Intel® CoreTM processorsChipsetIntel® H61 Express ChipsetLAN2 LAN portsCOM 2 COM portsDual Disp

61. Make sure the system and all other peripheral devices connected to it has been powered-off.2. Disconnect all power cords and cables.3. The 8

75. The memory socket, expansion slots, Mini PCIe slot and SATA drive bay are readily accessible after removing the chassis cover.SODIMM socket

83. Note the key on the socket. The key ensures the module can be plugged into the socket in only one direction.SODIMM socket1. Locate the DIMM

94. Grasping the module by its edges, position the module above the socket with the notch in the socket aligned with the key on the module. Apply rm