Dfi COM630-B Bedienungsanleitung

COM630-BSystem BoardUser’s ManualA01430151

110IntroductionI/O ConnectorsExpansion SlotsCOM ExpressConnectorsDimensions• 2 connectors for 4 additional external USB 2.0/1.1 ports• 1 connector for

112Hardware InstallationSystem Board LayoutChapter 2 - Hardware InstallationVGACOM 4COM 1COM 2LANUSB 0USB 1USB 2USB 3Mic-inLine-outLine-in11IrDA1WOR1C

122Hardware InstallationJP13 is used to select the power of the PS/2 keyboard/mouse port. Selecting 5V_standby will allow you to use

132Hardware InstallationJP5 (for USB 0-3) and JP6 (for USB 4-7) are used to select the power of the USB ports. Selecting 5V_standby will allow you to

142Hardware InstallationPanel Power SelectJP5JP3 is used to select the power supplied to the LCD panel.Important:Before powering-on the system, ma

152Hardware InstallationPower-on SelectJP14 is used to select the method of powering on the system. If you want the system to power-on

162Hardware InstallationCompactFlash Socket SettingJP15JP15 is used to set the CompactFlashTM socket to Master or Slave mode.Note:We do not recommend

172Hardware InstallationRear Panel I/O PortsThe rear panel I/O ports consist of the following:• PS/2 mouse port• PS/2 keyboard port• 3 COM ports

182Hardware InstallationThese ports are used to connect a PS/2 mouse and a PS/2 keyboard. The PS/2 mouse port uses IRQ12. Important:Make

192Hardware InstallationCOM 2COM 1COM 4The system board is equipped with 3 onboard serial ports (COM 1, COM 2 and COM 4). It is also equ

CopyrightThis publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to

202Hardware InstallationThe VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable connector to the VGA port.

212Hardware InstallationRJ45 LAN PortThe onboard RJ45 LAN port allows the system board to connect to a local area network by means of a

222Hardware InstallationUniversal Serial Bus ConnectorsUSB allows data exchange between your computer and a wide range of simulta-neously

232Hardware InstallationAudio Front audioRear AudioThe system board is equipped with 3 audio jacks. A jack is a one-hole connecting interface for inse

242Hardware InstallationFront AudioThe front audio connector allows you to connect to the line-out and mic-in jacks that are at the f

252Hardware InstallationI/O ConnectorsCD-in Internal Audio ConnectorThe CD-in connector is used to receive audio from a CD-ROM drive, TV

262Hardware InstallationS/PDIF ConnectorThe S/PDIF connector is used to connect external S/PDIF ports. Your S/PDIF ports may be mounted

272Hardware InstallationLVDS LCD Panel ConnectorLCD/Inverter Power ConnectorThe system board allows you to connect a LCD Display Panel by

282Hardware InstallationPins13579111315171921232527293133353739FunctionGNDLVDS_Out3+LVDS_Out3-GNDLVDS_Out2+LVDS_Out2-GNDLVDS_Out1+LVDS_Out1-GNDLVDS_Ou

292Hardware InstallationDigital I/O ConnectorDigital I/O Power ConnectorThe Digital I/O connector provides powering-on function to an externa

FCC and DOC Statement on Class BThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 o

302Hardware InstallationParallel Connector (optional)The parallel port is for interfacing your PC to a parallel printer. It supports SPP

312Hardware InstallationFloppy Disk Drive ConnectorThe oppy disk drive connector supports a standard oppy disk drive. The oppy cable can be in

322Hardware InstallationThe Serial ATA connectors are used to connect Serial ATA devices. Connect one end of the Serial ATA cable to a S

332Hardware InstallationIDE ConnectorImportant: We do not recommend using IDE devices and CF card at the same time.The IDE connector is used to

342Hardware InstallationImportant:If you encountered problems while using an ATAPI CD-ROM drive that is set in Master mode, please set th

352Hardware InstallationIrDA Connector15VCCN. C.IRRXGroundIRTXConnect the cable connector from your IrDA module to the IrDA connector.Note:The sequen

362Hardware InstallationCooling Fan ConnectorsThe fan connectors are used to connect cooling fans. The cooling fans will provide adequate airow throu

372Hardware InstallationChassis Intrusion ConnectorThe board supports the chassis intrusion detection function. Connect the chas-sis intrus

382Hardware InstallationPower Connectors1312241+3.3VDC+3.3VDCCOM+5VDCCOM+5VDCCOMPWR_OK+5VSB+12VDC+12VDC+3.3VDC+3.3VDC-12VDCCOMPS_ON#COMCOMCOMNC+5VDC+5

392Hardware InstallationWake-On-Ring ConnectorThe Wake-On-Ring connector is used to connect to an internal modem add-in card that has the

Table of ContentsCopyright ...2Trademarks ...

402Hardware InstallationStandby Power LEDStandby Power LEDDiagnostic LED Standby Power LEDThis LED will lit red when the system is in the s

412Hardware InstallationFront Panel ConnectorsHDD-LED - HDD LEDThis LED will light when the hard drive is being accessed.RESET SW - Reset SwitchThis s

422Hardware InstallationGPIO ConnectorThe General Purpose Input/Output (GPIO) peripheral provides dedicated general-purpose pins that can be c

432Hardware InstallationExpansion SlotsPCI Express x16 SlotInstall PCI Express x16 graphics card, that comply to the PCI Express specica-

442Hardware InstallationThe lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source of power when the m

452Hardware InstallationCompactFlash SocketCompactFlash socketThe CompactFlashTM socket is used for inserting a CompactFlashTM card. Compact-FlashTM

462Hardware InstallationCOM Express ConnectorsThe COM Express connectors are used to interface the carrier board with a COM Express board

472Hardware Installation1 GND 56 RSVD2 GBE0_MDI3- 57 GND3 GBE0_MDI3+ 58 RSVD4 GBE0_LINK100# 59 RSVD5 GBE0_LINK1000# 60 GND6 GBE0_MDI2- 61 RSVD7 GBE0_M

482Hardware Installation1 GND 56 RSVD2 GBE_ACT# 57 GPIO383 LPC_FRAME# 58 RSVD4 LPC_AD0 59 RSVD5 LPC_AD1 60 GND6 LPC_AD2 61 RSVD7 LPC_AD3 62 RSVD8 LPC_

492Hardware Installation1 GND 56 PEG_RX1-2 IDE_D7 57 RSVD3 IDE_D6 58 PEG_RX2+4 IDE_D3 59 PEG_RX2-5 IDE_D15 60 GND6 IDE_D8 61 PEG_RX3+7 IDE_D9 62 PEG_R

Internal I/O Connectors ... 25CD-in Internal Audio Connector ...

502Hardware Installation1 GND 56 PEG_TX1-2 IDE_D5 57 RSVD3 IDE_D10 58 PEG_TX2+4 IDE_D11 59 PEG_TX2-5 IDE_D12 60 GND6 IDE_D4 61 PEG_TX3+7 IDE_D0 62 PEG

16IntroductionAbout this ManualAn electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-R

17IntroductionStatic Electricity PrecautionsIt is quite easy to inadvertently damage your PC, system board, components or devices even before installi

18IntroductionAbout the PackageThe system board package contains the following items. If any of these items are missing or damaged, please contact you

19IntroductionChapter 1 - IntroductionSpecificationsAudioSerial ATAIDEBIOS(optional)I/O Chip 1I/O Chip 2Damage FreeIntelligenceTemperatureHumidityRear