Dfi DL310-C226 Bedienungsanleitung

1DL310-C226MicroATX Industrial MotherboardUser’s ManualA29540450

www.dfi .com10Chapter 2 Hardware InstallationChapter 2The system board supports the following memory interface. Single Channel (SC)Data will be accesse

www.dfi .com100Appendix D Troubleshooting ChecklistAppendix DAppendix D - Troubleshooting ChecklistTroubleshooting ChecklistThis chapter of the manual

www.dfi .com101Appendix D Troubleshooting ChecklistAppendix DHard DriveHard disk failure.1. Make sure the correct drive type for the hard disk drive h

www.dfi .com11Chapter 2 Hardware InstallationChapter 2CPUThe system board is equipped with a surface mount LGA 1150 socket. This socket is exclu-sively

www.dfi .com12Chapter 2 Hardware InstallationChapter 2Important:The CPU socket must not come in contact with anything other than the CPU. Avoid unneces

www.dfi .com13Chapter 2 Hardware InstallationChapter 2Important:The CPU will fit in only one orientation and can easily be inserted without exerting an

www.dfi .com14Chapter 2 Hardware InstallationChapter 2Installing the Fan and Heat SinkThe CPU must be kept cool by using a CPU fan with heat sink. With

www.dfi .com15Chapter 2 Hardware InstallationChapter 2Jumper SettingsClear CMOS DataIf you encounter the followings,a) CMOS data becomes corrupted.b)

www.dfi .com16Chapter 2 Hardware InstallationChapter 2JP4, JP5, JP6, JP8 and JP18 are used to select the power of the USB devices. Selecting +5V_standb

www.dfi .com17Chapter 2 Hardware InstallationChapter 2COM1/COM2 RS232/422/485 SelectJP2/JP11RS232RS422Full DuplexRS485COM 1/ COM 2 DCD-TDRDDTR-GND12345

www.dfi .com18Chapter 2 Hardware InstallationChapter 2Digital I/O Power Select Digital I/O Output StateJP131322-3 On: +5V1321-2 On: +5V_standby(default

www.dfi .com19Chapter 2 Hardware InstallationChapter 2SATA DOM Power Select2-3 On: +5V1-2 On: GND(default) Note:SATA port 5 provides adequate space fo

2CopyrightThis publication contains information that is protected by copyright. No part of it may be re-produced in any form or by any means or used t

www.dfi .com20Chapter 2 Hardware InstallationChapter 2Rear Panel I/O PortsThe rear panel I/O ports consist of the following:• 1 PS/2 Keyboard/Mouse po

www.dfi .com21Chapter 2 Hardware InstallationChapter 2COM (Serial) PortsCOM 3 to COM 6 are fixed at RS232.The pin functions of COM 1 and COM 2 port wil

www.dfi .com22Chapter 2 Hardware InstallationChapter 2RJ45 LAN PortsThe two LAN ports allow the system board to connect to a local area network by mean

www.dfi .com23Chapter 2 Hardware InstallationChapter 2Important:If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the +5V_stand

www.dfi .com24Chapter 2 Hardware InstallationChapter 2I/O ConnectorsSATA (Serial ATA) Connectors• 6 Serial ATA ports - 6 SATA 3.0 ports with data

www.dfi .com25Chapter 2 Hardware InstallationChapter 2The 8-bit Digital I/O connector provides powering-on function to external devices that are con-ne

www.dfi .com26Chapter 2 Hardware InstallationChapter 2Chassis Intrusion Connector The board supports the chassis intrusion detection function. Connect

www.dfi .com27Chapter 2 Hardware InstallationChapter 2Front Panel ConnectorHDD-LEDRESET-SWPWR-LEDATX-SW121121Front PanelParallel ConnectorThe 25-pin co

www.dfi .com28Chapter 2 Hardware InstallationChapter 2Expansion SlotsPCI Express x16 SlotInstall PCI Express x16 graphics card, that comply to the PCI

www.dfi .com29Chapter 2 Hardware InstallationChapter 2The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source of

3Copyright ...2Trademarks ...

www.dfi .com30Chapter 3 BIOS SetupChapter 3Chapter 3 - BIOS SetupOverview The BIOS is a program that takes care of the basic level of communication bet

www.dfi .com31Chapter 3 BIOS SetupChapter 3MainThe Main menu is the first screen that you will see when you enter the BIOS Setup Utility. System DateTh

www.dfi .com32Chapter 3 BIOS SetupChapter 3ACPI Power Management ConfigurationThis section is used to configure the ACPI Power Management.About Resume

www.dfi .com33Chapter 3 BIOS SetupChapter 3CPU ConfigurationThis section is used to configure the CPU. It will also display the detected CPU informatio

www.dfi .com34Chapter 3 BIOS SetupChapter 3When IDE mode is selected in the SATA Mode Selection, it will display the following information:Determines h

www.dfi .com35Chapter 3 BIOS SetupChapter 3Software Feature Mask Confi gurationRAID OROM/RST driver will refer to the SWFM configuration in order to ena

www.dfi .com36Chapter 3 BIOS SetupChapter 3AMT ConfigurationThis section configures the parameters of Active Management Technology.Aptio Setup Utility

www.dfi .com37Chapter 3 BIOS SetupChapter 3Super IO ConfigurationThis section is used to configure the I/O functions supported by the onboard Super I/O

www.dfi .com38Chapter 3 BIOS SetupChapter 3Enable or Disable Serial Port (COM)Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.Version

www.dfi .com39Chapter 3 BIOS SetupChapter 3Enable or Disable Parallel Port (LPT/LPTE).Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc

4About this ManualAn electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-ROM drive. The

www.dfi .com40Chapter 3 BIOS SetupChapter 3CPU Smart Fan ControlWhen this feature is set to Automatic, the CPU’s fan speed will rotate according to the

www.dfi .com41Chapter 3 BIOS SetupChapter 3Ipv4 PXE SupportWhen enabled, Ipv4 PXE boot supports. When disabled, Ipv4 PXE boot option will not be create

www.dfi .com42Chapter 3 BIOS SetupChapter 3Intel(R) I210 Gigabit Network Connection - 00:01:29:54...(Only for reference)This section is used to configu

www.dfi .com43Chapter 3 BIOS SetupChapter 3System Agent (SA) ConfigurationThis section is used to configure the parameters of System Agent.Check to ena

www.dfi .com44Chapter 3 BIOS SetupChapter 3 DVMT Pre-Allocated Selects DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal

www.dfi .com45Chapter 3 BIOS SetupChapter 3NB PCIe ConfigurationThis field is used to configure the settings of NB PCI Express. Confi gure PEG0 B0:D1:F0

www.dfi .com46Chapter 3 BIOS SetupChapter 3PCH-IO ConfigurationThis section illustrates the PCH parameters.Onboard I217 LAN ControllerEnables or disabl

www.dfi .com47Chapter 3 BIOS SetupChapter 3USB ConfigurationThis field is used to configure the USB settings.Precondition work on USB host controller a

www.dfi .com48Chapter 3 BIOS SetupChapter 3 XHCI Mode Selects the operation mode of XHCI controller. These options are Auto, Enabled, and Dis

www.dfi .com49Chapter 3 BIOS SetupChapter 3Control detection of the Azalia device.Disable= Azalia will be unconditionally disabledEnabled= Azalia will

5About the PackageThe package contains the following items. If any of these items are missing or damaged, please contact your dealer or sales represen

www.dfi .com50Chapter 3 BIOS SetupChapter 3CSM ParametersThis option controls if CSM will be launched. Aptio Setup Utility - Copyright (C) 2012 America

www.dfi .com51Chapter 3 BIOS SetupChapter 3Save & ExitReset the system after saving the changes. Aptio Setup Utility - Copyright (C) 2012 American

www.dfi .com52Chapter 3 BIOS SetupChapter 3Change this to enable or disable all features of Smbios Event Logging during boot.Aptio Setup Utility - Copy

www.dfi .com53Chapter 3 BIOS SetupChapter 3Notice: BIOS SPI ROM1. The Intel® Management Engine has already been integrated into this system board. Due

www.dfi .com54Chapter 4 Supported SoftwareChapter 4Chapter 4 - Supported SoftwareThe CD that came with the system board contains drivers, utilities and

www.dfi .com55Chapter 4 Supported SoftwareChapter 4For Windows XP Microsoft .NET Framework 3.5 (For Windows XP)To install the driver, click “Microsoft

www.dfi .com56Chapter 4 Supported SoftwareChapter 4Intel Chipset Software Installation UtilityThe Intel Chipset Software Installation Utility is used f

www.dfi .com57Chapter 4 Supported SoftwareChapter 43. Go through the readme document for more installa-tion tips then click Next.4. Click Finish to e

www.dfi .com58Chapter 4 Supported SoftwareChapter 4Intel HD Graphics Drivers (For Windows XP)To install the driver, click “Intel HD Graphics Drivers” o

www.dfi .com59Chapter 4 Supported SoftwareChapter 4Intel HD Graphics Drivers (For Windows 7 and Windows 8)To install the driver, click “Intel HD Graphi

6Chapter 1 - IntroductionSpecificationsChapter 1Chapter 1 Introduction www.dfi .comSerial ATA• 6 SATA 3.0 ports with data transfer rate up to 6Gb/s -

www.dfi .com60Chapter 4 Supported SoftwareChapter 4Intel Management Engine DriversTo install the driver, click “Intel Management Engine Drivers” on the

www.dfi .com61Chapter 4 Supported SoftwareChapter 4Audio DriversTo install the driver, click “Audio Drivers” on the main menu. 2. Click “Yes, I want t

www.dfi .com62Chapter 4 Supported SoftwareChapter 45. Select your hardware disk and then click "Have Disk..."4. Select a hardware type: DVD/C

www.dfi .com63Chapter 4 Supported SoftwareChapter 4Intel LAN Drivers (For Windows 7 and Windows 8)To install the driver, click “Intel LAN Drivers” on t

www.dfi .com64Chapter 4 Supported SoftwareChapter 44. Click Install to begin the installation.5. After completing installa-tion, click Finish.1. Setu

www.dfi .com65Chapter 4 Supported SoftwareChapter 43. Click “Install” to begin the installation.4. After completing installa tion, click “Finish”

www.dfi .com66Chapter 4 Supported SoftwareChapter 4WatchDogHW Health Set DIO

www.dfi .com67Chapter 4 Supported SoftwareChapter 4Intel USB 3.0 Drivers (For Windows 7)To install the driver, click “Intel USB 3.0 Driver” on the main

www.dfi .com68Chapter 4 Supported SoftwareChapter 4Intel Rapid Storage Technology (For Windows 7 and Windows 8)The Intel Rapid Storage Technology is a

www.dfi .com69Chapter 4 Supported SoftwareChapter 46. Click “Yes, I want to restart my computer now” then click Finish.Restarting the system will allow

7Chapter 1Features • Watchdog TimerThe Watchdog Timer function allows your application to regularly “clear” the system at the set time interval. If th

www.dfi .com70Chapter 4 Supported SoftwareChapter 4Infineon TPM Driver and Tool (optional)To install the driver, click “Infineon TPM driver and tool (o

www.dfi .com71Chapter 4 Supported SoftwareChapter 47. TPM requires installing the Micro-soft Visual C++ package prior to installing the utility. Click

www.dfi .com72Chapter 4 Supported SoftwareChapter 4Adobe Acrobat Reader 9.3To install the reader, click “Adobe Acrobat Reader 9.3” on the main menu.1.

www.dfi .com73Chapter 5 Digital I/O Programming GuideChapter 5Chapter 5 - Digital I/O Programming GuideRegister DescriptionThe Input Port Register (reg

www.dfi .com74Chapter 5 Digital I/O Programming GuideChapter 5Function DescriptionI2CWriteByte(SlaveAddr, SubAddr, Data): Write a Byte data to a specif

www.dfi .com75Chapter 6 RAIDChapter 6Chapter 6 - RAIDThe system board allows configuring RAID on Serial ATA drives. It supports RAID 0, RAID 1, RAID 5

www.dfi .com76Chapter 6 RAIDChapter 6Step 4: Install the RAID Driver During OS Installation The RAID driver must be installed during the Windows® XP or

www.dfi .com77Chapter 6 RAIDChapter 65. Go through the readme document to view system requirements and installa-tion information then click Next.7.

www.dfi .com78Chapter 7 Intel AMT SettingsChapter 7Chapter 7 - Intel AMT SettingsOverview Intel Active Management Technology (Intel® AMT) combines hard

www.dfi .com79Chapter 7 Intel AMT SettingsChapter 74. In the Save & Exit menu, select Save Changes and Reset then select OK. Enable Intel® AMT in t

8• Wake-On-PS/2This function allows you to use the PS/2 keyboard or PS/2 mouse to power-on the system.• Power Failure RecoveryWhen power returns after

www.dfi .com80Chapter 7 Intel AMT SettingsChapter 73. Enter a new password in the space provided under Intel(R) ME New Password then press Enter. The

www.dfi .com81Chapter 7 Intel AMT SettingsChapter 76. Select Change Intel(R) ME Password then press Enter. You will be prompted for a password. The

www.dfi .com82Chapter 7 Intel AMT SettingsChapter 79. In the Intel(R) AMT Configuration menu, select Manageability Feature Selection then press Enter.

www.dfi .com83Chapter 7 Intel AMT SettingsChapter 713. In the SOL/IDER/KVM menu, select IDER then press Enter. Select Disabled then press Enter. Inte

www.dfi .com84Chapter 7 Intel AMT SettingsChapter 717. Select Previous Menu until you return to the Intel(R) AMT Configuration menu. Select User Cons

www.dfi .com85Chapter 7 Intel AMT SettingsChapter 721. In the Intel(R) AMT Configuration menu, select Network Setup then press Enter. Intel(R) Manage

www.dfi .com86Chapter 7 Intel AMT SettingsChapter 725. Select Shared/Dedicated FQDN then press Enter. Select Shared or Dedicated then press Enter.Int

www.dfi .com87Chapter 7 Intel AMT SettingsChapter 729. Select Previous Menu until you return to the Intel(R) AMT Configuration menu. Select Activate

www.dfi .com88Chapter 7 Intel AMT SettingsChapter 733. In the Intel(R) Remote Setup And Configuration menu, select Provisioning Re-cord then press En

www.dfi .com89Chapter 7 Intel AMT SettingsChapter 737. In the Intel(R) Remote Automated Setup And Configuration menu, select TLS PSK then press Enter

www.dfi .com9Chapter 2 Hardware InstallationChapter 2Chapter 2 - Hardware InstallationBoard LayoutUSB 2-3/6-7Power Select (JP8)DDR3_1 DDR3_3DDR3_4DDR3_

www.dfi .com90Chapter 7 Intel AMT SettingsChapter 741. In the Intel(R) Remote Configuration menu, select Remote Configuration ** then press Enter. Se

www.dfi .com91Chapter 7 Intel AMT SettingsChapter 745. In the Intel(R) AMT Power Control menu, select Intel(R) AMT ON in Host Sleep States then press

www.dfi .com92Appendix A NLITE and AHCI Installation GuideAppendix AAppendix A - NLITE and AHCI Installation GuidenLitenLite is an application program

www.dfi .com93Appendix A NLITE and AHCI Installation GuideAppendix A7. Click Next.8. In the Task Selection dialog box, click Drivers and Bootable ISO.

www.dfi .com94Appendix A NLITE and AHCI Installation GuideAppendix A11. If you are uncertain of the southbridge chip used on your motherboard, select

www.dfi .com95Appendix A NLITE and AHCI Installation GuideAppendix A15. To create an image, select the Create Image mode under the General section an

www.dfi .com96Appendix A NLITE and AHCI Installation GuideAppendix AAHCIThe installation steps below will guide you in configuring your SATA drive to A

www.dfi .com97Appendix A NLITE and AHCI Installation GuideAppendix A8. Click “Have Disk”.9. Select C:\AHCI\iaAHCI.inf and then click Open.10. Select

www.dfi .com98Appendix B Watchdog Sample CodeAppendix BAppendix B - Watchdog Sample Code;Software programming example:;--------------------------------

www.dfi .com99Appendix C System Error MessageAppendix CAppendix C - System Error MessageWhen the BIOS encounters an error that requires the user to cor